âœˆī¸
Miltech Simulations Documentation Hub
Miltech Simulations MV-22B Tiltrotor
Miltech Simulations MV-22B Tiltrotor
  • 👋Welcome to the MV-22B
  • Product Information
    • â„šī¸Introduction
    • 📃Glossary
    • ❗Disclaimer and Credits
    • 🆘Product Support
    • 📄PDF Manual
  • Product Guides
    • â€ŧī¸Important Need-to-Knows
    • âąī¸Quick Start Guide
    • ✅Normal Procedures
    • âš ī¸Other Procedures
      • Blade Fold/Unfold and Wing Stow (BFWS) Procedures
      • Single-Engine Operations (Engine Failure)
      • APPR using NAV1/NAV2 (ILS Approach – Glideslope and Localizer)
      • In-Flight Refueling
      • Fuel Dumping
    • đŸ—ƒī¸Hardware Binding Guide
  • Aircraft and Systems
    • âœˆī¸Overview - Exterior
    • âœˆī¸Overview - Cockpit
    • âœˆī¸Aircraft Systems
      • đŸ–Ĩī¸Multi-Function Displays (MFDs)
        • Primary Flight Data (PFD)
        • Hover Mode (HVR)
        • Navigation Functions (NAV)
        • Forward-Looking Infrared Camera (FLIR)
        • Status Functions (STAT)
        • System Functions (SYST)
      • đŸ–Ĩī¸Center/Control Display Unit (CDU)
        • CDU - Menu 1
        • CDU - Menu 2
        • Flight Plan (FPLN) Menu
        • Waypoint (WYPT) Menu
        • Mission (MSN) Menu
        • Timer (TIMER) Menu
        • Exterior Lighting (LTS) Menu
        • Status Functions (STAT) Menu
        • Engine Instrument Crew Alerting System (EICAS) & Standby Flight Display
      • đŸŽ›ī¸Autopilot Console
      • đŸŽ›ī¸Communications Console
      • đŸ–Ĩī¸Standby Instruments
      • đŸŽ›ī¸Overhead Panel
      • đŸŽ›ī¸Center Console
      • đŸŽ›ī¸Side Consoles
    • đŸ—ēī¸FS24 - Navigation Systems
    • âš™ī¸Performance and Limits
    • đŸ“ĻCargo Load Capabilities
Powered by GitBook
On this page
  1. Aircraft and Systems
  2. Aircraft Systems
  3. Center/Control Display Unit (CDU)

Engine Instrument Crew Alerting System (EICAS) & Standby Flight Display

PreviousStatus Functions (STAT) MenuNextAutopilot Console

Last updated 1 year ago

Accessible through a single click of the EICAS button, or the CDU button. EICAS is by default always shown in the center of the CDU, except when navigating the STAT pages. The EICAS display is used to give the crew an overview of aircraft systems operation. Some of the key engine indications are also shown on the Standby Flight Display.

  1. Nacelle Angle Indicator

  2. Fuel Quantity

  3. Nr: Percentage of Nominal Proprotor Speed (rpm)

  4. Np: Percentage of Nominal Turbine Shaft Power

  5. Flaps Level Indicator

  6. ENG TRQ: Engine Torque

  7. Ng: Gas Generator Speed (e.g. compressor shaft)

  8. MGT: Measured Gas Generator Temperature

  9. OIL PSI: Oil Pressure

  10. HYD: Hydraulic Pressure: Hyd pressure must be at least 3800psi on at least one HYD system for nacelles to move.

  11. PRGB: Proprotor Gearbox oil Pressure/Temperature

  12. TAGB: Tilt Axis Gearbox oil Pressure/Temperature

  13. MWGB: Midwing Gearbox oil Pressure/Temperature

  14. Alerting System

âœˆī¸
đŸ–Ĩī¸
Figure: Standby Flight Display (Left), EICAS Display (Right)